Menu
Heidelberg GTOVP 52 + year: 1985 Impr.: 62 million Perfecting 2-2 / 4-0 varn Kompac Dampenning. Double sheet control Quick action plate clamps Weko powder spray plus Standard equipment available: immediately condition: very good price: 29.500 euro LOT / LOC M-M-TEC GmbH forest str. 30 86517 Wehringen / Germany Tel.: +4910 fax. VARN KOMPAC SEALS 5 SETS. VARN KOMPAC SEALS 10 SETS. A.B.DICK Find your Kompac Part Numbers Here PDF FILES. Kompac II complete backing plate kit $ V bushing $ Find great deals on eBay for Kompac in Commercial Printing Parts, Feeders, and SEAL BACKING PLATE FOR VARN KOMPAC III Kompac Metering Roller. China Kompac Iii, Kompac Iii from China Supplier – Find Variety Kompac Iii from, Printing Machinery Parts Suppliers Located in China, Buy Kompac Iii. Pdf manuals; blankets; deals videos; select press model. 2800cd series; 3200cd series; 3200mcd & (wide) 3200pfa & pcx; 3300cr & 3300mr; 3302m series; 3302h & 3304h; 3404 di series; 520 series; 524hx parts press; crestline. 3302m 5 roll (altra) 3302m 4 roll; 3302m 6 roll; 2800cd 4 roll; 3200cd 4 roll; 3200e 4 roll; 3200mcd 5 roll; kompac.
- Take the Kompac off the machine and separate the rollers. Place the Kompac on a sheetof white bond paper on a light table. Bring the rollers slowly together until they just touch.-make a complete revolution of the rollers. No light should show through. Light would showonly through depressed spots in the rollers (Low spots.) Operators putting excess pressure between rollers to compensate for low spots often cause ink burst marks (tracks) in the printedcopy, sometimes confused with gear streaks or toning at the outer edges of the plate.
- Calibrate the unit: Separate the rollers with the numbered calibrating knobs, disregarding thenumbers. Use two strips of paper to set a slight drag equally on each side of the roller. It is importantto the operation of the Kompac that the rollers are as parallel as possible.
- Remove the small outer slotted screw from the calibration knobs and use a 3/32 hex wrench toloosen and reset the knobs to corresponding numbers.
- Replace and retighten screws with both knobs set at the number “1”. “0” should separate therollers, “2-2’/2” should be the operating position.
- The numbers on the calibrating knob should always correspond when the rollers are exactlyparallel. Never operate the unit with the knobs out of calibration after they have been set correctly.
- With a plate on the machine, set the Kompac in the brackets on the machine without the spring.Let the Kompac fall down on the plate cylinder to assume a parallel position on the plate cylinder.Tighten the Kompac to a slight drag in the slotted brackets to hold the unit in place.
- Hand operate the machine to ink up the Kompac and take an ink stripe. There should be an exact parallel stripe across the plate. (Do not Operate the machine under power without the springsattached.)
- If the stripe is not parallel tap the slightly tightened Kompac up or down in the slot until it makes aperfectly parallel stripe.
- Tighten the Kompac in the brackets and attach the springs.
- With the plate still attached, operate the Press in the water position and adjust the unit to a veryslight bounce evenly on both sides. Do not operate the machine with excessive bounce.
- Add ink to the press and ink up the plate to a dense black. Stripe the Kompac form to be certainthe roll is parallel. If not, make a slight adjustment.
- Allow the form and fountain rolls to make contact for 10-15 seconds, place the single lever in thewater position, use the hand wheel to make a rapid 1/4 inch turn opposite the nip. The ink burst stripshould be approximately 1/8 and parallel. This will show the rollers are correctly calibrated.
- Check the PH of the fountain solution. Use the manufactures minimum recommendation usually4.0 – 4.5 acid and 5.5 – 6.0 alkaline.
- Add fountain solution to the Kompac and with the press operating at a slow speed drop the formon the inked plate.
- After dropping the Kompac rollers on the inked plate, the rollers should begin removing the inkevenlyacross the plate within 4-5 revolutions and clean the plate completely and evenly across in 20-25revolutions.
- With the press off and the Kompac lifted off the plate, the plate should immediatelybegin drying evenly. Patches of water or excess water at the bottom of leading edges indicate morepressure is needed between rollers.
- Excessive revolutions or inability of Kompac to remove ink from the plate indicate more water –or less pressure between the roller nip.
- An area left inked in the middle of the plate can mean a slight low spot in the rollers of the unit.
- An uneven cleanup across the plate means the rollers are not parallel.
- Water droplets or a complete instant removal of ink along the edge of the plate indicate leakingseals, or a weak pressure – plate ‘against the seal.
- If rollers leave a residue or spots of balled-up ink segments, check chemicals or PH.
- Kompac should remove all ink leaving a shiny, clean plate.
- If the plate is clean at the front edge, but tones at the trailing edge, more pressure is needed formto plate. 24. Ink piling at lead edge bend of plate indicate too much roller pressure, glazed rollers, orchemicals causing excessive need of pressure.
- A small amount of buildup in the plate edge over long runs is common. Stop the press and cleanleading edge when needed.
- Kompac will not operate properly with:
- Low spots in the rollers
- Glazed rollers
- Long or excessively soft ink or ink mixed with certain dryers
- Unbalanced PH in water fountain solution
- Rollers not parallel across plate
- Kompac tilted or binding in mounting frames
- Certain fountain solutions and inks are not compatible with the Kompac
- Paper plates made by certain manufacturers without their recommended
Cached. NOTE: Kompac has discontinued manufacturing the 92260 seal. If you are still using these oldstyle seals, you will need to buy the 92280 upgrade kit to use new style seals.
We have been the main UK agent for the sale of Kompac dampening systems since 1994 when the company was called Varn International.
T: +44 (0)1249 811 435
F: +44 (0)1249 813 377
E: [email protected]
© 2007 Ray Canter Print Engineers
![Manual Manual](/uploads/1/1/7/9/117906709/459015251.jpg)
Since then the company has separated to concentrate on their own key areas. This has lead to Kompac now offering out its own range of chemicals including fount solutions, press washers & plate/blanket cleaners.
Kompac Kwik Finish
New for late 2007 will see the launch of the Kompac Kwik Finish coating & curing system. We are pleased to be able to confirm that we are the sole UK & Ireland agent for the sale of the Kwik Finish coater & ancillary equipment.
The Kwik Finish will be of interest to anyone who currently produces or wants to produce UV coated material. The press works on offset & digital printed material & can produce a flood coating across the entire sheet or do a spot coating of a particular area.
Varn Kompac 3 Manual
Honda cb1 manual. Download the Kompac Kwik Finish brochure (PDF)